HappyModel CrazyBee X V2.2 F4 1-2S AIO Whoop Flight Controller (F4 FC / 5A 4in1 ESC / 25-200mW VTX) - Choose Your RX

$50.99
Coming Soon
In Stock
Pre Order
Receiver
Free Delivery on U.S.A. Orders $60 or more
Add to Wishlist

Version two of the CrazyBee X AIO, also a replacement for the Crux3.

Be sure to check out all our Whoop FCs and our HappyModel gear collection!

Specifications

  • Weight: 4.4g

Flight Controller

  • MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
  • Sensor: MPU-6000 (SPI Connection)
  • Board Size: 28.5 * 28.5mm
  • Power Supply: 1S-2S battery input (DC 2.9V-8.7V)
  • Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
  • Built-in Betaflight OSD(SPI Control)
  • Built-in 5.8G VTX
  • Built-in SPI Frsky receiver support D8/D16 (
  • Built-in 5V 1A BEC
  • Built-in voltage detection
  • Firmware Target:
  • CrazybeeX FR Version: Recommend Betaflight 3.5.7 target CRAZYBBEF4FR
  • CrazybeeX FS version: Recommend Betaflight 3.5.7 target CRAZYBBEF4FS
  • CrazybeeX PNP version: Recommend Betaflight 3.5.7 target CRAZYBEEF4DX


Onboard 5A 4In1 ESC

  • EFM8BB21
  • Power Supply: 1-2S LiPo/LiPo HV
  • Current: 5A continuous peak 6A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory Firmware: S_H_50_REV16_7.HEX
  • Default Protocol: DSHOT600


CrazybeeX FR V2.2 Version Onboard Frsky SPI Receiver (Optional)

  • SPI BUS Receiver Frsky D8/D16 Compatible
  • Support for Futaba S-FHSS (Need Betaflight 4.0.5 firmware or latest), Frsky_X_LBT(EU-LBT)
  • Channels: 8CH / 16CH
  • Failsafe support
  • No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m

 

CrazybeeX PNP V2.2 Version W/O on Board Receiver (Optional)

  • No Onboard SPI Receiver


Onboard 5.8G 40CH VTX

  • Output Power: 25mw~200mw switchable
  • Frequency: 40CH
  • Input voltage: 3.3V 5.5V
  • Current consumption: 300mA(type)
  • Frequency: 5.8GHz 5bands 40 channels
  • With Race band
  • Smartaudio ready
  • Default vtx_power is 3
  • Should set vtx_low_power_disarm = ON to reduce the high temperature when test on the ground.


Onboard Voltage and Current detector

  • Voltage Meter scale “110”
  • Amperage Mete scale “1175”

Includes

  • 1x HappyModel CrazyBee X V2.2 F4 AIO Whoop Flight Controller (F4 FC, 5A 1-2S 4in1 ESC, 25-200mW VTX) 

CrazybeeX FR V2.2 Bind procedure:

  1. Make the on board receiver get into bind mode: Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; Or use bind code to bind :For 3.5.7 version firmware Plug USB and then connect Betaflight configurator and then move to CLI tab , type “Frsky_bind”, the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.0.x the bind code is “bind_rx_spi” ,For 4.1.x or 4.2.x the bind code is “bind_rx”
  2. Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink.   The red LED wouldn't blinking when binding with some new ACCESS firmware frsky radio  , but the bind is actually successful , need to go to CLI command and type “save” to finish the binding .

CrazybeeX FS V2.2 Bind procedure:

  1. Make the on board receiver get into bind mode: For 3.5.7 version firmware Press and hold the bind button for 1 second ,then plug USB, the Red LED at the bottom of the flight controller will blinking fast , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED at the bottom of the flight controller will blinking fast , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
  2. Make your Flysky transmitter get into bind mode . If bind is successful the red led will getting to be solid.
x