Matek F765-WING Flight Controller

$67.99
In Stock
Pre Order
Coming Soon
Add to Wishlist

The F765-WING is an incredibly feature rich wing flight controller that supports Betaflight, iNav and ArduPilot. If you love connecting all sorts of peripheral devices to your setup (like GPS or even airspeed sensors), this FC has the connectivity! Just check out the features below.

Check out all our wing parts & our Matek gear selection!

Features

  • STM32F765VI Processor
  • Dual Gyros (MPU6000 & ICM20602)
  • BMP280 Barometer
  • OSD
  • 7x UARTs
  • 2x I2C
  • 12x PWM outputs
  • 3x BEC
  • Camera switcher

Specifications

FC 

  • MCU: STM32F765VIT6, 216MHz , 512KB RAM, 2MB Flash
  • IMU: MPU6000 (SPI1) & ICM20602 (SPI3)
  • Baro: BMP280 (I2C2)
  • OSD: AT7456E (SPI2)
  • Blackbox: MicroSD card slot (SDIO)
  • 7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
  • 1x Softserial1_Tx (INAV)
  • 12x PWM outputs (S1~S10 support Dshot)
  • 6x ADC (VBAT, Current, RSSI, Analog AirSpeed, VB2, CU2)
  • 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
  • 2x I2C
  • 1x SPI4 breakout
  • Switchable Dual Camera Inputs
  • Switchable 5V/9V(12V) for Camera/VTX
  • High-precision Current Sense
  • ADC VB2 voltage divider: 1K:10K
  • ADC AirSpeed voltage divider: 10K:10K
  • TR/SA VTX control: Yes
  • WS2812 Led Strip : Yes
  • Beeper : Yes
  • RSSI: Yes
  • Analog Airspeed sensor: Yes
  • Digital Airspeed sensor: Yes

Firmware

  • INAV Target: MATEKF765
  • ArduPilot(ChiBiOS)  Target: MATEKF765-WING

PDB

  • Input voltage range: 9~36V (3~6S LiPo) w/TVS protection
  • 2x ESC power pads
  • Battery Voltage Sensor: 1:10 (Scale 1100 in INAV,  BATT_VOLT_MULT 11.0 in ArduPilot)
  • Current Senor: 132A,  3.3V ADC  (Scale 250 in INAV,  40 A/V in ArduPilot)

BEC 5V output

  • Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
  • Continuous current: 2 Amps, Max.3A

BEC 9V /12V output

  • Designed for Video Transmitter, Camera, Gimbal ect.
  • Continuous current: 2 Amps, Max.3A
  • 12V option with Jumper pad

BEC Vx output

  • Designed for Servos
  • Voltage adjustable, 5V Default, 6V or 7.2V via jumper
  • Continuous current: 8 Amps, Max.10A

BEC 3.3V output

  • Designed for Baro / Compass module and Spektrum RX
  • Linear Regulator
  • Continuous current: 200mA

Physical

  • Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
  • Dimensions: 54 x 36 x 13 mm
  • Weight: 26g

Includes

  • 1x Matek F765-WING Flight Controller
  • 1x Pin Header Set

Notes

  • Camera switch & Vsw switch are not supported by ArduPilot now
  • Camera-1 and Vsw On by default with ArduPilot firmware
  • Rx5 is not supported for now.
  • No VB2 and CU2 definitions in INAV target
  • If FC board and top BEC plate are not connected via Vbat/G/Vx ,  you might solder other BEC output to FC Vx and G pad for powering up servos.
  • OSD font uploading could break off in MacOS  INAV configurator, pls use Windows version.
  • If using 2 cameras, both should be set with identical video format, both PAL or both NTSC.

Manual Download

Firmware Download

x