Holybro Kakute F7 AIO F7 Flight Controller w/ OSD BEC Current Sensor & 4 PCS 65A BLheli_32 Tekko32 F3 Metal ESC Stack/Combo

$135.60
In Stock
Pre Order
Coming Soon
Add to Wishlist
Holybro Kakute F7 AIO F7 Flight Controller w/ OSD BEC Current Sensor & 4 PCS 65A BLheli_32 Tekko32 F3 Metal ESC Combo 

Specificaiton:
Brand Name: Holybro
Model: Kakute F7 AIO & Tekko32 F3 Metal Combo

Tekko32 F3 Metal ESC  
Model: Tekko32 F3 Metal Item Name: 65A BL_32 DShot1200 ESC Quantity: 4 PCS Con. Current: 65A Peak Current: 80A Input Voltage: 3-6S Lipo Support Ext. cap needed for 6s (220uf 35v for 6s usage.) - F3(M4 Core) MCU, Runs BLHELI32 firmware, the MCU works at 108Mhz - Mosfet tested at 4S 65A, under props, nothing covered for 1min - Onboard WS2812B LED Size: 18 x 27 mm Weight: 4.4g/PC
Kakute F7 AIO  ( Manual)
Item Name: F7 Flight Controller AIO OSD BEC and Current Sensor
MCU: STM32F745 32-bit processor IMU: ICM20689 (SPI) Barometer: BMP280 Current Sensor: Approximately 130 amps maximum measurable value USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART) 6 hardware UARTS (UART1,2,3,4,6,7) All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”. Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. TF card for Blackbox logging Dimensions: 35x48x7mm (includes foam-mounted gyro board in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 11g

Features:
• Supports Betaflight, Butterflight, and Cleanflight. • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level,   all using your transmitter sticks and goggles. • Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need   to soft-mount the board itself. • High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate. • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units. • 2 oz. copper PCB allows up to 120A maximum continuous current. • Dedicated bootloader button for easy firmware flashing. • Low-profile design fits into even very compact frames. • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only). • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 AIO monitors voltage directly   from the battery power lead. • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power   peripherals such as receiver, video transmitter, FPV camera, or LED strip. • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Diagram picture link: https://blog.seidel-philipp.de/holybro-kakute-f7-aio-flight-controller-anschlussplan-wiringplan/

Package Included:
4x Holybro ekko32 F3 Metal ESC 65A 4x 35V 220uF Capacitor 4x 24AWG 100mm Black wire  4x 24AWG 100mm White wire  4x 24AWG 100mm Blue wire  4x 16AWG 100mm Red wire  4x 16AWG 100mm Black wire 
1x Kakute F7 Flight Controller Board
 

 








You recently viewed

Clear recently viewed
x