HappyModel BNF Mobula7 Whoop - Basic or Standard Kit - FRSKY, DSMX, FLYSKY

$95.99
$93.99
In Stock
Pre Order
Coming Soon
Add to Wishlist

***If the button says "Add to Cart", the item is in stock and ships immediately!***

Whoops have gone to the next level! The Mobula7 has taken the internet by storm given its speed and capabilities in such a small package. Check out the video and specs of the Mobula 7 by Happy Model below!



Tune

Your Mobula7’s flight controller controls its flight through settings known as PIDS. Changing these changes the characteristics of your quad’s flight. RDQ’s recommended Mobula7 tune is:

set p_pitch = 65
set i_pitch = 80
set d_pitch = 50
set f_pitch = 96
set p_roll = 65
set i_roll = 80
set d_roll = 50
set f_roll = 96
set p_yaw = 65
set i_yaw = 75
set d_yaw = 0
set f_yaw = 100

 

To setup this tune, connect your Mobula7 to betaflight and click the CLI tab. Copy and paste the above settings in, hit enter, type save, then hit enter again. Enjoy your Mobula’s improved flight characteriestics! 

The new betaflight configurator 10.5.0 and 10.5.1 are not compatible with Mobula7 and Mobula7 HD for now. HappyModel suggests using Betaflight configurator 10.4.0 

Specification: 
Brand Name: Happymodel
Model: Mobula 7
Item Name: 75mm Wheelbase 2S Brushless Whoop FPV Racing Drone
Wheelbase: 75mm

Version: Basic Version / Standard Version ( Optional)
- The diffirence of them are the package charger.
   Basic Version: USB Charger
   Standard Version: 6-way Charger

Receiver ( Optional): Compatible Frsky NON-EU Receiver
                                      Compatible Frsky EU-LBT   Receiver  ( XM+ Receiver)
                                      Compatible Flysky AFHDS/ AFHDS-2A Receiver
                                      Compatible DSM2/DSMX Receiver

Size: 98mm*98mm*36mm

Weight: 25.9g (without battery)
This is compatible with our 250mah HV Whoop Batteries

Crazybee F3 Pro Flight Controller Item Name: Crazybee F3 Pro FC
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1-2S battery input (DC 3.5-8.7V)

Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Receiver ( Diffirent version having diffirent receiver)
Built-in Betaflight OSD(SPI Control)
Built-in Current meter Max 28A
Current meter scale set to 1175
Built-in 5V 1A BEC with LC filter

Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready

Firmware
(Frsky version) CRAZYBEEF3 PRO FR Firmware target: CrazybeeF3FR
(Flysky version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS
(DSM2/DSMX version) CRAZYBEEF3 PRO Firmware target: CrazybeeF3DX
(Frsky EU-LBT version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS
 
Onboard 5A 4 In 1 ESC

Power supply: 1-2S LiPo/LiPo HV (3.5v/8.7v)
MCU upgraded to EFM8BB21
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7
Default protocol: DSHOT600

Onboard Frsky NON-EU receiver Version
SPI BUS receiver
Frsky D8/D16 switchable
Compatible Non EU transmitter both D8 and D16 mode

Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 
Onboard Frsky EU-LBT Version
(External XM+ receiver)
 

Operating Voltage Range: 3.7~10V
Operating Current: 30mA @5V
Operating Range: Full range
With RSSI output on board: Analog 0~3.3V
Firmware Upgradeable, Default firmware EU-LBT with RSSI

Onboard Flysky receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 

Onboard DSM2 / DSMX receiver version

Serial bus receiver
Protocol: DSM2/DSMX compatible
Channels:6-9 (Depend on your radio)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 
SE0802 16000KV Motor
Model: SE0802
KV: 16000KV
Configu-ration: 9N12P Stator Diamter: 8mm Stator Length: 2mm Shaft Diameter: Φ1.0 Motor Dimension (Dia.*Len) : Φ10.5*14.5mm Weight: 1.8g
Support 1-2S Lipo
 
No.of Cells: 1S Lipo
Propeller
40mm 4-blade Propeller ( 4 CW + 4 CCW)
 

5.8G VTX AIO Camera
 

5.8G 40CH 25mW VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)

700TVL FOV120 Camera
Camera resolution: 700TVL
Field of view: 120°
Video Format: NTSC
Antenna: RG178 antenna
Frequency: 5.8GHz 5bands 40 channels
With Raceband
Smartaudio ready(Frsky EU-LBT and DSMX version not compatible)
Size: 13.9"12.0mm ( L*W )
Weight: 3g
 
Lipo Battery
Capacity:250mAh
Voltage:3.8v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 55mmx12mmx7mm
Weight: 6.5g
Connector: PH2.0
Notes: Need 2pcs batteries for Series circuit
 


Features:
- New Crazybee F3 PRO Flight controller 1-2s Lipo compatible
- 2S whoop more powerful and more flight time
- Betaflight support , multi flight mode: ACRO/AIR/ANGLE
- New 0802 Powerful and High efficiency Brushless motor and Smooth ESC
- Smartaudio ready , change VTX bands, channels via OSD
  DSM2/DSMX and Frsky EU-LBT version are Serial-based receiver, so Smartaudio is not compatible.
- Adjust the settings and the PID of the flight controller via OSD
- Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible
- Flysky version support both AFHDS and AFHDS-2A protocol transmitter
- DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter
- Frsky EU-LBT version support Frsky EU-LBT firmware transmitter
- Full telemetry function ready
- Head lights ready
- Camera angle adjustable
- Real Bind and Fly version
- Buzzer Ready

Package Included:
Basic Version
1x Mobula7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
4x 3.8v 250mah 30C/60C Lipo battery
1x USB Lipo/LIHV Charger
1x Fixing Mount for Lipo Battery
1x Propeller Disassemble Tool
1x Screwdriver

Standard Version
1x Mobula7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
4x 3.8v 250mah 30C/60C Lipo battery
1x 1S06 6 Way Lipo/LIHV charger
1x Propeller Disassemble Tool
1x Fixing Mount for Lipo Battery

1x Screwdriver 


Mobula7 Whoop by HappyModel
Mobula7 Basic Kit


FRSKY Whoop
Standard Whoop Kit

Mobula7






FPV REGULATORY NOTICE

The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your areaIt is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. RDQ cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.

Customer Reviews

Based on 23 reviews Write a review

You recently viewed

Clear recently viewed
x