HolyBro Kakute F7 AIO V1.5/ Tekko32 F3 Metal ESC Stack/Combo (F7 FC, 32Bit 65A ESC)

$129.99
Coming Soon
In Stock
Pre Order
Free Delivery on U.S.A. Orders $50 or more
Add to Wishlist

Top of the line individual ESC and FC combo from Holybro.

Check out all our FC/ESC Stacks and Combos, and all our Holybro Products!

Features

Tekko32 F3 Metal ESC (BLHeli32)

  • New BLHELI32 ESC with F3 MCU, give more smooth control and faster responding speed.
  • Supports up to 80A burst and 65A continued. (ESC mounted under props, without anything covered on the ESC)
  • The latest Tekko32 F3 Metal ESC has improvemed in both performance and appearance. Enhanced BEC, withstand voltage up to 80V.

      Kakute F7 AIO V1.5

      • Supports Betaflight, Butterflight.
      • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
      • Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
      • High-performance / low-noise / high sensitivity IMU. MPU6000 with 6-axis gyro and accelerometer. 
      • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
      • 2 oz. copper PCB allows up to 120A maximum continuous current.
      • Dedicated bootloader button for easy firmware flashing.
      • Low-profile design fits into even very compact frames.
      • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
      • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 AIO monitors voltage directly from the battery power lead.
      • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
      • Supports BLHeli pass-through for easy ESC upgrade and configuration.


        Specifications

        Tekko32 F3 Metal ESC (BLHeli32)

        • F3(M4 Core) MCU, Runs BLHELI32 firmware, the MCU works at 108Mhz
        • Mosfet tested at 4S 65A, under props, nothing covered for 1min
        • 18 x 27 mm 
        • Supports Lipo 3-6S
        • Ext. cap needed for 6s (220uf 35v for 6s usage.)
        • Onboard WS2812B LED
        • Weight: 4.4g (1pcs)

        Kakute F7 AIO V1.5

        • MCU: STM32F745 32-bit processor
        • IMU: MPU6000 (SPI)
        • Barometer: BMP280
        • Current Sensor: Approximately 130 amps maximum measurable value
        • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
        • 6 hardware UARTS (UART1,2,3,4,6,7)
        • All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
        • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
        • TF card for Blackbox logging
        • Dimensions: 35x48x7mm (includes foam-mounted gyro board in height)
        • Mounting Holes: Standard 30.5mm square to center of holes 
        • Weight: 11.2g

          Includes

          • 1x Holybro Kakute F7 AIO V1.5/ Tekko32 F3 Metal ESC Stack/Combo (F7 FC, 32Bit 65A ESC)
          x