Holybro Kakute F7 / Tekko32 / Atlatl HV V2 30x30 Stack/Combo (F7 FC, 32Bit 35A 4in1 ESC, 25-800mW VTX)

$124.99
Coming Soon
In Stock
Pre Order
Add to Wishlist

Holybro saves you time and guesswork in coming up with your perfect FPV stack. This stack combines the Kakute F7 FC, Atlatl HV V2 VTX, and the Tekko32 4-in-1 ESC.

The Holybro Kakute F7 flight controller makes it easy to build your multirotor. It integrates flight controller (FC) and on-screen display (OSD) in one. The Kakute F7’s layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy. 

Tekko32 is a powerful 35A 4in1 ESC with BLHELI32 firmware natively supports ESC Telemetry function.

The original Atlatl was an excellent VTX for many users, it performed well, however some design choices led to issues for some such as the antenna mounting direction. Holybro has gone ahead and changed a few key elements to make this VTX a serious contender for your quad. The tiny button is now larger and easier to press, the MMCX connector is now facing outwards, and it now goes all the way up to 800mW for those who are cruising freestyle. Some much-appreciated changes!

 

Check out all our FC/ESC Stacks and Combos, and all our Holybro Products!

Kakute F7 Features

  • Supports Betaflight, Butterflight, and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
  • High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate.
  • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
  • 2 oz. copper PCB allows up to 120A maximum continuous current.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.
  • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Kakute F7 Specifications

  • MCU: STM32F745 32-bit processor
  • IMU: ICM20689 (SPI)
  • Barometer: BMP280
  • Current Sensor: Approximately 130 amps maximum measurable value
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 6 hardware UARTS (UART1,2,3,4,6,7)
  • All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
  • TF card for Blackbox logging
  • Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 9g

Manual: http://www.holybro.com/manual/Holybro_Kakute_F7_Manual.pdf

Tekko32 Features

  • 4in1 ESC with 30.5x30.5mm mounting holes, supports DSHOT 1200, BLHELI32 firmware.
  • On this version added more CAPS to reduce power noise.
  • 32bit ESC with BLHELI32 firmware
  • 4PWM input
  • Voltage output (VBAT), ESC Telemetry(TELEM)
  • Supports Oneshot / Multishot / Dshot PWM
  • Supports damped light
  • NO BEC

Tekko32 Specifications

  • Supports 3-6S lipo input
  • 35A continuous current, 50A burst
  • Mounting holes 30.5x30.5mm
  • Size:55*40*6.4mm
  • Weight: 17g

Atlatl HV V2 Feautres

  • Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
  • Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.
  • SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.
  • All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.
  • MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.
  • LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad.
  • Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.
  • 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.
  • Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly.
  • Standard 36mm form factor allows you to mount the Atlatl directly on your flight controller stack.

Atlatl HV V2 Specifications

  • Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
  • Audio: 6.5 MHz Mono
  • Antenna Connector: MMCX
  • Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts
  • Dimensions: 35x25x7mm (Includes USB height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 9.3g

Includes

  • 1x Tekko32 4in1 ESC board
  • 1x Kakute F7 FC
  • 1x Atlatl HV V2
  • 1x 8pin to 8pin 1mm pitch cable

Manual: http://www.holybro.com/manual/Holybro-Atlatl-HV-v2-Manual.pdf

Kakute F7 Wiring Guide

You recently viewed

Clear recently viewed
x