Matek F722 Mini SE 20x20 Flight Controller

$39.99
In Stock
Pre Order
Coming Soon
Add to Wishlist
Free Delivery on U.S.A. Orders $50 or more

The Matek F722-Mini SE has been improved over the previous NON SE version and now has a BMP280 Barometer. 

Check out the entire Matek selection!

    Specifications

    • MCU: 216MHz STM32F722RET6
    • IMU: MPU6000 (SPI)
    • OSD: AT7456E (SPI)
    • Baro: Infineon DPS310 (I2C)
    • Blackbox: 32M-byte Flash memory (SPI)
    • 5x Uarts (1,2,3,4,6) with build-in inversion
    • 1x Softserial supported
    • 8x Dshot/Proshot/oneshot outputs
    • 1x I2C
    • 1x SH1.0_8pin connector (Vbat/G/Curr/R6/S1/S2/S3/S4)
    • 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red)
    • Vbat filtered output power for VTX,  Switchable via AUX (modes tab-user1)
    • Dual Camera image switchable via AUX (modes tab-user2)
    • Convertible 20mm to 30.5mm mounting
    • Camera control: Yes
    • Smartaudio & Tramp VTX protocol: Yes
    • DJI OSD: Yes (any spare Uart Tx & Rx)
    • WS2812 Led Strip : Yes
    • Beeper : Yes
    • RSSI: Yes
    • Additional ADC for INAV analog airspeed
    Power
    • Input: 6~36V (2~8S LiPo)
    • BEC: 5V 2A
    • LDO 3.3V: Max.200mA
    • Battery Voltage Sensor: 1:10 (Scale 110)
    • No Current Sensor built-in, supports external current sensor of PDB/4in1
    Firmware
    • INAV target: MATEKF722mini
    • BetaFlight unified target: MATEKF722mini(MTKS)
    • BetaFlight legacy target: MATEKF722SE
    Physical
    • Mounting
      • 20 x 20mm/Φ3mm with Silicon Grommets
      • 20 x 20mm/Φ2mm with Silicon & Brass Grommets
      • 30.5 x 30.5mm/Φ3mm with Conversion Plate and Silicon Grommets
    • Dimensions:  28 x 28 mm

    Includes

    • 1x Matek F722-Mini SE 30x30 Flight Controller

     

     

    Pad/Hole Pin name Function BetaFlight INav INav INav
    Multirotor Multirotor Tricopter Plane
    S1 PB4 TIM3_CH1 motor-1 motor-1 motor-1 servo
    S2 PB5 TIM3_CH2 motor-2 motor-2 motor-2 servo
    S3 PB0 TIM3_CH3 motor-3 motor-3 motor-3 servo
    S4 PB1 TIM3_CH4 motor-4 motor-4 servo
    S5 PA15 TIM2_CH1 motor-5 motor-5 servo
    S6 PB3 TIM2_CH2 motor-6 motor-6 servo
    S7 PB6 TIM4_CH1 motor-7 servo servo motor-1
    S8 PB7 TIM4_CH2 motor-8 servo motor-2
    LED PA8 TIM1_CH1 2812LED 2812LED 2812LED 2812LED
    RX2 PA3 TIM9_CH2 RX2/ppm RX2/ppm RX2/ppm RX2/ppm
    TX2 PA2 TIM9_CH1 TX2/pwm1 TX2 TX2 TX2
    RX4 PA1 TIM5_CH2 RX4/pwm2
    Cam_Ctrl
    RX4 RX4 RX4
    TX4 PA0 TIM5_CH1 TX4/pwm3
    PA4 PA4 ADC AirSpeed

     

    • INAV2.5.1 and Betaflight 2.4.x downloaded from configurator don’t support new barometer DPS310.
    • DPS310 will be supported officially by INAV2.6/ BetaFlight 4.3 and new configurator.
    • For now, pls download customized INAV2.5.1 and BetaFlight 2.4.0 from here.

    inav_2.5.1_MATEKF722MINI_DPS310.hex

    If Baro can’t be detected. In INAV CLI mode, type command

    • set baro_hardware = DPS310
    • save

    betaflight_4.2.0_MATEKF722MINI_DPS310.hex

    If Baro can’t be detected. In BF CLI mode, type command

    • set baro_bustype = I2C
    • set baro_i2c_device = 1
    • set baro_i2c_address = 118
    • set baro_hardware = DPS310
    • save
    x