RDQ Bardwell F7 3-6s 30x30 Stack/Combo (JBF7 FC / 32Bit 50A 4in1 ESC)
The next generation of RDQ Bardwell Flight Controller is here! Packed with features including an F7 processor, ICM20602 Gyro, several DC power outputs, DJI Air Unit Plug and 8 motor outputs! You can build just about anything, HD or Analog around this FC! Here's what JB has to say:
I'm Joshua Bardwell. This is MY flight controller. No Compromises. I made a list of all the features I wanted, and they made if for me. It's backed by RaceDayQuads' top-notch customer support. It's affordably priced. Oh, and let's not forget, technical support from none other than me: The FPV Know-It-All himself.
This bundle pairs the new Bardwell F7 Flight Controller with the iFlight Succex 32Bit 50A 4in1 ESC.
Check out the full range of RDQ Products!
Features
RDQ Bardwell F7 3-6S 30x30 Flight Controller - JBF7 FC
- Manual written, and feature set selected by Joshua Bardwell (see below)
- Board layout focused on flexibility and resilience. You can build what you want, how you want, without stress
- 4in1 plug also has solder pads for those who want to direct solder.
- Plug-and-play support for DJI Air Unit. Voltage regulator allows up to 6S input
- Seperate DJI and Analog targets with default customized for each use
- 8 motor pads foreasy resource remapping (or build an octocopter)
- SD card for blackbox logging
iFlight Succex 32Bit 50A 30x30 4in1 ESC
- 8 layer double-sided PCB
- 4oz 1.6mm thick power board(0.9mm copper ratio),better operating load capacity
- 32bit FO51K86 MCU, 48mHz maximum clock speed
- TDK MLCC Low ESR ceramic capacitors
- Top grade NTMFS5C430NL MOSFET
- Rational layout, countersunk holes on extended solder pads to ensure PCB layer connection
Specifications
RDQ Bardwell F7 3-6S 30x30 Flight Controller - JBF7 FC
- Input Voltage: 3-6S LiPo
- Processor: STM32F7
- Gyro: ICM20602
- Power Outputs: 5V, 3.3V, 9V, VBatt
- BF Target: JBF7 (analog), JBF7_DJI (for DJI)
- UARTs: 5, SDA/SCL (i2c)
- Interfaces: 4in1 ESC Plug & DJI Air Unit Plug
- Mounting Pattern: 30.5x30.5mm
- Weight: 8.4g
iFlight Succex 32Bit 50A 30x30 4in1 ESC
- Input Voltage: 2-6S
- STM32F051 MCU, 48Mhz Runs BLHELI 32.X Firmware
- Current sensor: Yes
- Telemetry:Supported
- BEC: No
- Dimension: 43x39mm
- Mounting Pattern: 30.5x30.5mm
- Weight: 14.4g
- Supports: DShot DShot150/300/600/1200/MultiShot/ OneShot etc.
- Target: iFlight-BL32-4IN1
Joshua Bardwell's Comprehensive Manual
The Betaflight target for this board is JBF7 (for analog) or JBF7_DJI (for DJI). These targets set up the Ports tab for analog or DJI use. JB has created a more detailed config dump, which includes custom OSD, JB's rates, and other configuration options more like he would set the quad up. If you want to try this out, the config diffs are linked below.
Includes
- 1x RDQ Bardwell F7 30x30 Stack/Combo (F7 FC and 32Bit 50A 3-6s 4in1 ESC)
*DJI Air Unit and Stack Screws Not Included