TinysLEDs Unity Mini F7 V1.1 20x20 Flight Controller

$35.99
Coming Soon
In Stock
Pre Order
Free Delivery on U.S.A. Orders $50 or more
Add to Wishlist

TinysLEDs packed everything they liked from the Whitenoise Synergy board and crammed it into a 20x20 FC. 

New V1.1 Updates

  • LED connector: Add 2 LEDs to your build easy with built in LED connector and cables. Fits all Tiny's LEDs Rainbow series (With or without connectors) LED CONNECTOR IS UNDER USB port. DO NOT PLUG ESC INTO THIS CONNECTOR.
  • Buzzer pads moved to end of main LED connector. Wires included to easily wire up buzzer. Just plug in the buzzer wires included.
  • Easy Placement reminders on which side components go. mount Pin headers to cover the White blocks for VTX and Receiver.
  • Smart Audio Solder bridge to remove FC connection to SmartAudio pin. (this is utilized if you want to control vtx with CRSF protocol. Featured only on Crossfire and Tracer Nano RXs. Remove bridge to disconnected from FC TX3 pin.

Check out all our 20x20 Flight Controllers and all our TinysLEDs products!

Features

  • Buzzer pads for external buzzer
  • Built in camera control pin with resistor and capacitor
  • RealPit VTX pit mode switch
  • ESC Connector pads below connector
  • M4 Can be selected either led_strip signal or M4 signal for RPM filtering
  • Direct Mounting for TBS Nano Pro32/Pro VTX and XM+/TBS Nano RXs
  • LED on board for lighting up pods or displaying status info. 

Specifications

  • MCU: STM32F722RET6 216MHz
  • Gyro: MPU6000
  • OSD: Betaflight
  • Input Voltage: 3-6S LiPo
  • Buzzer Pads: Yes
  • Voltage Sensor: Yes
  • BEC: 5V/2A shared with LED strip
  • UARTS: 6
  • UART 3 TX: VTX Smart Audio
  • UART 1: RX/TX Receiver pins
  • Camera Control: Yes
  • 5 Full UARTS with RX AND TX pins
  • TX3,RX3 can be used for I2C for external compass
  • 5V VTX & CAM power
  • 16MB Blackbox flash chip
  • RealPit VTX pit mode switch
  • ESC Connector pads below connector
  • M4 Can be selected either led_strip signal or M4 signal for RPM filtering
  • LED on board for Status or other functions
  • Mounting Pattern: 20x20mm
  • Size: 25x25mm
  • Weight: 4g

Includes

  • 1x TinysLEDs Unity Mini F7 20x20 Flight Controller

 


Please follow setup directions for TBS Unify PRO32. You will need to flash Betaflight 4.1.x+  for the new Smartaudio 2.1 compatibility. 

https://github.com/betaflight/betaflight/blob/master/docs/VTX.md

TBS Nano 25/50mW NOTE:

If you are running a TBS Unify Nano please flash the  Synergy 3.5.7 AKK patch for the software patch to use Smart Audio 2.0 Lite. If you do not have a 10k ohm Resistor on your Nano mounting board adapter have Smart Audio issues. 

For a little bit faster boot time Enter these commands in CLI:

resource i2c_sda 2 none
resource i2c_scl 2 none
Set gyro_2_bustype = NONE

Until Official BF target of UNITYF7 is released use CLRACINGF7(CLRA) with the following commands below. 

use these CLI Commands for setting VTX Switch:

RESOURCE PINIO 1 C15

set pinio_box = 40,41,42,43

save

 Go to your Modes tab and setup " USER 1" to an aux channel to setup the pit switch. 

If you would like it to always be on. then set up " USER 1" to your arm channel and increase the bar to the entire span of the channel range.

 

 

 **If you want to have ALWAYS ON vtx power Setup Up your mode switches like this:

x