GEPRC BNF Run HD3 3" Micro Quad w/DJI Air Unit - Choose Your RX

In Stock
Pre Order
Coming Soon
Add to Wishlist
Free Delivery on U.S.A. Orders $50 or more

RUN HD3 with the latest DJI HD FPV System achieves high-definition FPV from a 3-inch mini Quad! RUN HD3 is designed for freestyle flight. 

The redesigned frame can ensure stability, the propeller will not show in view during flight, and the video can be completely for editing. Match with sufficient power 1507 3600KV motor, very handy for doing any maneuvers.

Engineered, professionally assembled and tuned by GEPRC team. You have to try this one!

Available configured with DJI Air Unit as receiver, or with FrSky XM+

Check out all our DJI compatible gear, our pre-built quads and our GEPRC selection


  • No Propellers in the view.
  • Perfect for DJI FPV HD
  • Full 3K Carbon Fiber
  • 720p 120fps FPV
  • System:STABLE PRO F7 35A
  • Black Box: 32Mb onboard flash memory.
  • Full Soft Mounted FC System: Provides a clean operating environment for gyro.
  • Exquisite Assembly Process: Eliminate any potential installation problems.
  • Weight:200g(without battery) 



  • Full 3K Carbon Fiber
  • Mounting Holes: 30.5*30.5mm/20*20mm
  • Side plate : 1.5mm
  • Top plate : 2mm
  • Bottom plate : 3mm
  • Side plate : 2mm
  • Wheelbase : 155mm
  • Motors: GR1507 3600KV
  • Recommended Battery:4S 850mAh (No inclueded)
  • Operating Frequency: 5.725-5.850 GHz
  • Transmitter Power (EIRP): FCC/SRRC: <30 dBm; CE: <14 dBm
  • Min. Latency (end-to-end)
  • Low Latency Mode (720p/120fps): <28 ms
  • High-Quality Mode (720p/60fps): <40 ms
  • Max. Transmission Distance: FCC/SRRC: <4 km; CE: <0.7 km
  • Video Format: MP4 (Video format: H.264; Audio format: ACC-LC)
  • I/O Interface: USB-C, MMCX, 3-in-1 port, microSD card slot
  • Operating Temperature Range: 32° to 104°F (0° to 40°C)
  • Input Power: 7.4-17.6 V, about 4-9 W
  • Sensor: 1/3.2” CMOS; Effective Pixels: 4 M
  • Lens: 2.1 mm, f/2.1
  • Shutter: Rolling shutter
  • ISO: 100-25600
  • FOV: 150°(D); 122°(H); 93°(V)
  • Dimension: 22.1 × 21.1 × 20.1 mm
    Electronic System(STABLE PRO F7 35A) STABLE PRO F7 Flight Controller
    • Model:STABLE PRO F7 35A
    • MCU: STM32F722RET6
    • IMU: 2x ICM20689(SPI)
    • BlackBox: 32Mb onboard Flash
    • OSD: BetaFlight OSD w/ AT7456E chip
    • Baro:NO
    • BEC Output: 5V@3A
    • Integrated LC Filter
    • Input Voltage: 2-6S Lipo
    • Firmware target: EXF722DUAL
    • Size: 26x26mm board, 20mm mounting holes (M2)
    STABLE PRO F7 ESC BL32 2-6S 4in1
    • MCU:STM32F051
    • Constant:35Amps
    • Burst:45Amps
    • Dimensions:31*31mm(including the power pads)
    • Mounting Holes:20*20mm,M2
    • Supports Dshot1200,Proshot,Oneshot,Multishot
    • Current meter: Yes
    • Target: GEPRC-BL32-4IN1


    • 1x RUN HD3 Quadcopter