iFlight BNF Protek35 Analog 4S 3.5" Quad - Choose Receiver Type

iFlight BNF Protek35 Analog 4S 3.5" Quad - Choose Receiver Type

$300.99

In Stock

Pre Order

Receiver Type

PNP

ELRS

Quantity

Free Delivery on U.S.A. Orders $99 or more

Add to Wishlist

Description

After our very popular 3-inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.

Our all-new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here.

ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all-new 2205 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to its 3inch predecessor which gives a lot more room for a lot more fun. Our GPS-measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch-outs or light freestyle moves.

A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization).

Note: Battery, GoPro, and GoPro mount are NOT included.

Check out our other pre-built quads, as well as the rest of our iFlight selection!

Features

High-performance True-AIO Board Beast Whoop F7 AIO 55A v2.0 to save weight and space
T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)
Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)
Low Resonance frame construction (Less Jello, more Cinematic footage)
Pre-tuned with smooth freestyle settings
Butter smooth 2205 3200KV (4S)
ProTek35 Prop Guards V2.0
No Props or frame in view!

Pre-Tuned & Pre-Setup:

Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning were applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable Angle-Mode, and activate Acro-Mode"

Specifications

Beast F7 V2 AIO FC

MCU: BGA-STM32F745
Gyro: BMI270
Blackbox: 8Mb Onboard Flash
BEC output: 5V 2.5A
Barometer: BMP280
Connector: Micro-USB
OSD: AT7456E
FC Firmware：IFLIGHT_F745_AIO_V2
Mounting pattern: 25.5x25.5mm φ3mm
Dimensions: 32.5x32.5mm
Weight: 8.5g

F7 55A 2-6S ESC

Current Sensor: Yes
Input: 2-6S LIPO
Current scale: 200
Constant: 55A
BLHeli: BLHeli-S
Telemetry: no
ESC Firmware: BlheliS G-H-30
Mounting pattern: 25.5x25.5mm/Φ3mm
Dimensions: 32.5x32.5mm

SucceX Mini Force 5.8GHz 600mW VTX

Power: PIT/25/200/400mW/600mW
Antenna interface: MMCX
VTX protocol: IRC Tramp
Output 40 channels.
Size: 29x29mm
Mounting pattern: 20x20Φ3/25x25 mmΦ2
Weight: 4g

Includes

1x ProTek35 Frame
2x Albatross RHCP RP-SMA 5.8g antenna
1x TPU Antenna holder
2x Nazgul 3535 propeller (Set of 4 - Color May Vary)
1x iFlight Lipo Strap 15x150mm (Color May Vary)
1x iFlight Lipo Strap 15x250mm (Color May Vary)
1x GoPro TPU bottom stand black (GoPro Protector not included)

Filters

Amp Rating

Connector

Input Voltage

Kv

Manufacturer

Motor Bolt Pattern

Prop Pitch

Shaft Size

Stack Size

Stator Size

Cinewhoop Gear

iFlight BNF Protek35 Analog 4S 3.5" Quad - Choose Receiver Type

Support

Additional Links

Subscribe

Follow us