SpeedyBee F405 WING APP 2-6S Fixed Wing Flight Controller
Original price
$39.99
-
Original price
$39.99
Original price
$39.99
$39.99
-
$39.99
Current price
$39.99
In Stock
Pre Order
$39.99
The SpeedyBee F405 WING APP flight controller has been tailor-made for FPV fixed-wing pilots. Its STM32 F405 MCU and ICM-42688-P IMU, 6 UARTS, and Bluetooth enable superb performance and unbeatable flying. You get top-notch features, such as OSD, a barometer and an onboard RGB battery indicator, all at an amazing price. Wireless setup is simple, and very minimal soldering is needed with all the plugin ports. It supports both INAV and Ardupilot firmware, and Ardupilot's VTOL function too! This amazing wing flight controller will allow you to use up to 11 PWM outputs to be configured for motors and servo control.
Check out our other wing flight controllers, and our SpeedyBee products!
Features
- Wireless configuration
- Easy installation, plug and play - no soldering needed
- Dual firmware support for INAV and Ardupilot
- Support Ardupilot's VTOL function
- F405 all pins break out
- Multilayer board design, stable operation
- CRSF telemetry data displayed by Lua script
- 4x LED strip plugs, lighting style
- On-board current sensor, with 3 BEC outputs
- Includes 90° pin headers, for lower installation height
Specifications
SpeedyBee F405 WING FC board- MCU: STM32F405,168MHz,1MB Flash
- IMU(Gyro&Accelerometer: ICM-42688-P
- Barometer: SPL006-001
- OSD Chip: AT7456E
- Blackbox: MicroSD Card Slot
- UART: 6 sets(USART1, USART2, USART3, UART4, UART5, UART6(Dedicated for Wireless board Telemetry connection))
- I2C: 1x Used for magnetometer, digital airspeed sensor
- ADC: 4x (VBAT, Current, RSSI, Analog AirSpeed)
- PWM: 12x (11+1“LED”pad)
- ELRS/CRSF receiver: Supported,connected to UART1
- SBUS: Built in inverter for SBUS input (UART2-RX)
- LED: 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) 1x RGB
- RSSI: Supported, Named as RS .
- Supported FC Firmware: INAV:SpeedyBeeF405WING(default)ArduPilot: SpeedyBeeF405WING
- Weight: 8.9g
- Input voltage range: 7~36V (2~6S LiPo)
- Battery Voltage Sensor: Connect to FC board VBAT, 1K:10K (Scale 1100 in iNav, BATT_VOLT_MULT 11.0 in ArduPilot)
- Battery Current Sensor: 90A continuous, 215A peak Connect to FC board Current (Scale 195 in iNav, 50 A/V in ArduPilot)
- TVS Protective diode: Yes
- FC BEC output: Output 5.2V +/- 0.1V DC Continuous current 2.4 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed module, Telemetry module, WS2812 LED_Strip
- VTX BEC output: Output 9V +/- 0.1V DC Continuous current 1.8 Amps, 2.3A Peak Voltage adjustable, 9V Default, 12V or 5V via jumper Designed for Analog Video Transmitter,Digital Video Transmitter, Camera.
- Servo BEC output: Output 4.9V +/- 0.1V DC Continuous current 4.5 Amps, 5.5A Peak Voltage adjustable, 4.9V Default, 6V or 7.2V via jumper Designed for Servos.
- Weight: 11.4g
- Wireless Configuration (long press BOOT button for 6 seconds to switch modes) BLE mode, connect to Speedybee APP
- Wi-Fi mode, connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc.
- Classic Bluetooth SPP mode, connect to QGroundControl APP, MissionPlanner
- LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes) 4x WS2812 LED strip connectors, adjustable colors and flashing modes
- Max 5.2V 1.3A, supports around 70pcs 5050 WS2812 LED beads
- On-board battery level indicator: 4x RGB indicator LED for battery level display by a number of lights
- Weight: 4.2g
Includes
- 1x SpeedyBee F405 WING APP Fixed Wing Flight Controller
