• HAPPYMODEL AIO FC HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
  • HAPPYMODEL AIO FC HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
  • HAPPYMODEL AIO FC HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version
1 3

HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version

HappyModel SuperBee F4 Lite AIO Whoop Flight Controller - Choose Version

$50.49
$50.49
Receiver:
Add To Wishlist
View full details

Details

Description

It's finally here! The ultralight 1s 5a AIO of the future comes in at a clean 2.8g. This is the AIO that got the mobula6 HDZero whoop under 25 grams.

Be sure to check out all our Whoop FCs and our HappyModel gear collection!

Due to this flight controller being a spare part for Mobula6 HDZERO, the original default device for OSD is “MSP”

If you bought this flight controller and used it for an analog camera, you may need to change some settings. First, connect to Betaflight Configurator, then move to CLI command tab, and enter “set osd_displayport_device = MAX7456”,  then reconnect Betaflight, and upload the osd font.

Specifications

  • Board size: 25 x 25
  • Power supply: 1S
  • Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
  • Built-in Betaflight OSD(SPI Control)
  • Built-in 5V 1A BEC
  • Built-in voltage detection
  • MCU upgraded to EFM8BB21
  • Support BLHeliSuite programmable
  • Factory firmware: S_H_50_REV16_8.HEX
  • Default protocol: DSHOT150/DSHOT300/DSHOT600

FRSKY SPI BUS RECEIVER

  • Frsky D8/D16 switchable
  • Compatible Non-EU transmitter in both D8 and D16 mode
  • Channels: 8ch or 16ch
  • Failsafe support
  • No ground interference (Transmitter and receiver 1 m from the ground): 300m

    ELRS SPI RECEIVER

    • Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
    • RF Frequency: 2.4GHzAntenna plug: IPEX
    • Telemetry output Power: <12dBm
    • Receiver protocol: SPI ExpressLRS
    • Could bind with ELRS V2.0 firmware TX module

          Includes

          • 1x HappyModel SuperBee F4 Lite AIO Whoop Flight Controller
          • 1x PH2.0 Pigtail
          • 1x Hardware Set

          More Info

          • SKU: 20541
          • Barcode: 691023522305
           

          Overall rating: 3.7222223 / 5 from 18 reviews.

          AI Generated Review Summary

          Summary topics

          Review topics: ["issues","board","pads","audio"].

          Review highlights

          Reviews

          Perfect

          "Awesome fc, works amazingly well with hdzero"

          — David S. (5/5)

          Okay.

          "Dent board, but prone to typical HM quality issues. ICM gyro is not ideal. This board was better when they were using the BMI270 gyro. Solder pad layout is decent to work with."

          — Wesley W. (3/5)

          Light as a feather. Bring your Soldering Skills

          "Super light board, great deal for the price. Make sure you're skilled in the soldering department.... Tiny tiny pads next to even tinier caps."

          — Joseph R. (4/5)

          Not a good board, poor Quality Control

          "I have had 5 of these boards recently from Happy model and only 2 is currently working. Issues from lifted soldering pads to soldering pads not being there to USB connection not working to FC not working, poor QC, would not recommend"

          — Magnus T. (2/5)

          Bought as replacment on mobula

          "Bought as replacment on mobula 7 hdo . Esdy swap"

          — Wesly C. (5/5)

          Not impressed

          "Fragile and flakey board. This is the replacement board for the mob7 walksnail whoop the whoop has acted only on the original bnf, nor re arming after landing for example. I replaced it because esc3 had died. The replacement does it also. Maybe it just doesn't have the power to supply the hd system? Maybe I should have bought the x12?"

          — Jim P. (3/5)

          Great for Walksnail

          "Used this with the walksnail Lite board and camera on a 65mm whoop. Great board for HD. Make sure your soldering skills are up to par. Very small pads."

          — James L. (5/5)

          Great product.

          "This aio was exactly what I needed to get my baby nazgul 65mm back going again. It has plenty of power and haven't had any issues with it. Thanks again"

          — Bradley E. (5/5)

          Blown fet

          "Plugged in to USB first thing, all good. Soldered all my motors on, plugged in with smoke stopper, all good. Plugged in 1s lipo to check motor rotation, blew a FET. This is the second board I’ve had burn up before it ever made the first flight. I’ve built 20+ quads so I’m not new. These boards are not good"

          — william b. (1/5)

          Bootloader issues

          "Won't go into Bootloader when bridging the boot pads. So beware. It is brickable. 5v pad lifted very easy. Good thing there are two. No SWC and SWC pads labeled. Found poorly documented UART1."

          — Ryan P. (3/5)

          Q&A