• HOBBYWING FC Hobbywing XRotor F7 3-6S 20x20 / 30x30 Convertible Flight Controller
  • HOBBYWING FC Hobbywing XRotor F7 3-6S 20x20 / 30x30 Convertible Flight Controller
  • HOBBYWING FC Hobbywing XRotor F7 3-6S 20x20 / 30x30 Convertible Flight Controller
1 3

Hobbywing XRotor F7 3-6S 20x20 / 30x30 Convertible Flight Controller

Hobbywing XRotor F7 3-6S 20x20 / 30x30 Convertible Flight Controller

$54.99
$54.99
In stock
In stock
Add To Wishlist
View full details

Details

Description

Take a look at the XRotor F7 Convertible Flight Controller from Hobbywing. This FC is similar to other versions with its OSD, and voltage monitoring, but the F7 now comes with an all-new 5V & 12V dual BEC Circuit and a special interface for the DJI image transmission system. The XRotor F7 Convertible flight controller is equipped with STM32F722 MCU which has a powerful computing ability and fast running speed. High sensitivity ICM20602 six-axis motion sensor, built-in 5V & 12V double BEC, integrated OSD, and a pitch module.  

Check out our other flight controllers, and our Hobbywing selection!

Features

  • Equipped with STM32F722 MCU which has powerful computing ability and fast running speed, and high sensitivity MPU6500 six-axis motion sensor.
  • Supports BetaFlight, Cleanflight, Butterflight, Inva, and other mainstream FPV firmware.
  • DJI image transmission system port equipped with corresponding flat cable
  • Supports bidirectional DShot digital throttle communication.
  • Unique installation design and shock absorption structure.
  • On-board large capacity Flash memory chip.
  • On-board 5V & 12V dual BEC circuit.
  • On-board Pit Switch module.


Specifications

  • Firmware: HOBBYWING_XROTORF7CONV
  • FC Programming: Supported
  • Programming via Betaflight/ Cleanflight-configurator
  • Compatible with (Modes) PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600, PROSHOT1000
  • Compatible with (Transmitters) PPM, Spektrum, SBUS, SUMD, SUMH, XBUS, IBUS, JETIEXBUS, CRSF, SRXL
  • OSD Built-in
  • Input Voltage: 3-6S
  • Gyro: MPU6500
  • Voltage Monitoring Supported
  • Current Monitoring Supported
  • External Buzzer Supported
  • LED Control Supported
  • BEC 5V @ 1.5A ; 10V @ 1.5A
  • Mounting Pattern: 20x20mm M3 / 30x30mm M3
  • Size 32x32mm
  • Weight 3.3g

 Manual Download

    Includes

    • 1x Hobbywing XRotor F7 3-6S 20x20 / 30x30 Convertible Flight Controller
    • 1x Soft Mounting Grommets Set
    • 1x Signal Cable
    • 1x User Manual

    More Info

    • SKU: 16574
    • Barcode: 6938994414760
     

    Overall rating: 4.7 / 5 from 10 reviews.

    AI Generated Review Summary

    Summary topics

    Review topics: [].

    Review highlights

    Reviews

    Works like a charm.

    "This flight controler works great. I had to realign the pins from the fc to the esc, but other than that it's cheap and it works just as well as the old one."

    — Nate M. (4/5)

    So far so good.

    "Haven't flown it yet. Everything went well with the install and all functions seem to work. FYI the battery must be plugged in for anything to work. Not crazy about that. Just unplug the vtx before doing your setup, kind of a pain. The 5 volt reg. outputs 5. 2 volts which might be why it cannot be powered by the usb."

    — Brian I. (4/5)

    Firmware mystery...

    "I just received mine from getFpv (June 2022) and the installed firmware was FLYWOOF7DUAL 4.1.1 Nov 15 2019. It was also configured for a hex (#mixer mixer HEX6X). In the "Layout & Different Ports of the FC" section of the manual (section 03) it specifies the correct firmware as HOBBYWING_XROTORF7CONV. However, in the section titled "How to Flash the Firmware" (section 08) it warns "For avoiding any damage to the FC, please do not flash the unit with any firmware besides 'FLYWOOF7DUAL.' I flashed the HOBBYWING_XROTORF7CONV firmware and it seems to be OK, but I haven't had enough air time with it to be certain. The configuration it came with would not have been flyable with a quad. The unit seems to be very well made, it is conformal coated, and the layout makes sense. Regarding plug and play: There are several cables - be certain you check the pin outs before using. The cable that is correct for the HW 60A ESC is the one with the reassigned ground. My first impressions would rate it 5 stars but I reduced it to 4 because of the inconsistency in the manual."

    — Klaus (4/5)

    Reliable tried and true components

    "No complaints, while it might not be on the leading edge of FC technology. It provides a clean reliable package with proven successful components."

    — Justin O. (5/5)

    Simple to use

    "It works and my quad fly's. Simple to use. Simple to put it in."

    — Matthew L. (5/5)

    Flexible for most builds

    "Having either 20x20 or 30x30 is a nice feature works well with any accompanying hobbywing esc’s"

    — william F. (5/5)

    Great FC

    "Great FC"

    — David G. (5/5)

    Nice fc

    "Pretty nice, easy to solder, Hobbywing always has quality stuff, flies great and smooth"

    — Lucas M. (5/5)

    Can't go wrong with Hobbywing.

    "It's a great FC for a great price. Paired right up to my Hobbywing 60A ESC."

    — Seth D. (5/5)

    Always a solid investment

    "Hobbywing is an exceptional company This flight controller is a solid addition to any serious quad. Racing or freestyle this is my go to flight controller and they are usually in stock when others are not."

    — CHRISTOPHER T. (5/5)

    Q&A