• IFLIGHT AIO FC iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Controller (w/ 55A 8Bit 4in1 ESC)
  • IFLIGHT AIO FC iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Controller (w/ 55A 8Bit 4in1 ESC)
  • IFLIGHT AIO FC iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Controller (w/ 55A 8Bit 4in1 ESC)
  • IFLIGHT AIO FC iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Controller (w/ 55A 8Bit 4in1 ESC)
  • IFLIGHT AIO FC iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Controller (w/ 55A 8Bit 4in1 ESC)
  • IFLIGHT AIO FC iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Controller (w/ 55A 8Bit 4in1 ESC)
1 6

iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Controller (w/ 55A 8Bit 4in1 ESC)

iFlight Blitz Whoop F7 AIO [V1.1] 2-6S AIO Toothpick / Whoop Flight Controller (w/ 55A 8Bit 4in1 ESC)

$131.99
$131.99
In stock
In stock
Add To Wishlist
View full details

Details

Description

This is our new iFlight BLITZ series AIO FCs for your ultimate build. A future proof all-in-one FC to step up the game and make some more room for future flight firmware development like Betaflight, Emuflight etc. Lightweight, minimum size, minimum work.This could only be achieved by using BGA chipsets instead of ordinary QFP (big size) MCUs and ultra powerful Mosfets for almost any build. Solder your motor wires on and let's go! 

 Check out our other AIO FCs, as well as the rest of our iFlight selection!

Features

  • Separated Flight Control board to minimize electrical gyro noise
  • Pass-through DJI O3 and Caddx Vista/Polar Connector
  • FC PCB can be disassembled from the ESC PCB; Repair allowed!
  • MCU: BGA-STM32F745, 216MHz
  • OSD: AT7456E
  • Blackbox: 16MB Onboard Flash
  • Gyro: BMI270

Specifications

FC Specifications
  • MCU: BGA-STM32F745
  • Gyro: BMI270
  • Blackbox: 16MB Onboard Flash
  • BEC output: 5V 2.5A 
  • WS2812 LED Strip: Yes
  • Buzzer: Yes
  • Barometer: DPS310
  • Connector: Micro-USB
  • OSD: IFLIGHT OSD (AT745E）
  • FC Firmware：IFLIGHT_BLITZ_F7_AIO
  • Mounting pattern: 25.5 x 25.5mm φ3mm
  • Dimensions: 35mm x 35mm
  • Weight: 10.5g 
  • BEC: 5V 2A / 3A
  • Input voltage: 2-6S, support LIHV battery
  • Smartaudio / IRC Tramp VTX protocol supported
ESC Specifications
  • ESC MCU: BB21
  • Driver: FD6288
  • Input voltage: 2-6S Support LIHV battery
  • Output current: 55A, peak value 65A (10 seconds)
  • ESC firmware: Q-H-40 - Bluejay, 0.16, 24kHz
  • Current sensor: ratio 200 (1/10mV/A)
  • BEC: NO
  • ESC Telemetry: NO
  • Bidirectional DShot: Yes(need to use Bluejay firmware)
  • Supports DShot DShot150/300/600/MultiShot/ OneShot etc.

Includes

  • iFlight Blitz Whoop F7 AIO V1.1 (w/ 55A 8Bit 4in1 ESC)
  • 2 x Capacitor 470uF/35V
  • 1 x XT30U Male 18AWG cable 70mm
  • 1 x 1.0-7P cable 50mm-28mm
  • 1 x 1.0-7P cable 50mm
  • 4 x M2 silicon grommets
  • 8 x M2x12mm screws
  • 8 x M2 Transparent Nylon Nut
  • 10 x 0.8mm black Heat shrink tube 10mm


Wiring Diagram

More Info

  • SKU: 22249
  • Barcode: 691023520493
 

Overall rating: 4.0 / 5 from 2 reviews.

AI Generated Review Summary

Summary topics

Review topics: [].

Review highlights

Reviews

Very good

"It is installed and flying I think it is good AIO so far very good product"

— HALLY F. (5/5)

Enable BOTH serial ports 2 & 3

"Running this iFlight Blitz whoop F7 AIO (1.1) with DJI Air03. Could not get the stick inputs to register when testing in Betaflight. Product doc shows Serial connection on port 3, but when using the DJI wiring harness, you need to enable serial on BOTH ports 2 & 3. Luckily I figured out using the harness as the PIN labeling is completely illegible on the board, and I couldn't find any helpful docs in that regard. Hope this helps and happy flying!"

— JEBariffic (3/5)

Q&A