Description

Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1S Will be the best choice in the whoop season.  This is an amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX ranges by using this flight controller. The new RS0802 motors come with a new unibell design, uses a 1.5mm shaft, and includes a PCB bottom plate, which means high efficiency, and much more reliability.

Check out the rest of pre-built quads and our HappyModel selection!

Due to Runcam Nano3 camera was discontinued, now the Mobula7 1s comes with Caddx ant camera since May 2024. The Mobula7 1s with Caddx ant camera we called V2 version.

Features

We’re glad to launched our new Mobula7 drone , this time the 75mm whoop based on 1s power. Thanks to the new AIO flight controller and the new third-generation RS0802 brushless motor, the new Mobula7 1s Will be the best choice in the whoop season.

The world first 5-IN-1 AIO flight controller with ExpressLRS 2.0 , OPENVTX(up to 400mw), 12A Brushless Blheli_S ESC and Betaflight OSD coming out recently. This is amazing flight controller for Brushless whoop. You could get unbelievable RX and VTX range by using this flight controller.

The new RS0802 motors comes with a new unibell design, use 1.5mm shaft and include PCB bottom plate, high efficiency and much more reliable.

New onboard OpenVTX , max power up to 400mw, provide RCE and PIT mode, it was very useful for race event.

• X12 5-IN-1 AIO flight controller built-in 2.4G ELRS V2.0 and Openvtx
  
• VTX Power up to 400mw
  
• ELRS V2.0 Support
  
• NEW RS0802 KV20000 motors
  
• Caddxfpv ANT 1/3 CMOS 1200TVL Camera
  
• Smooth and powerful
  
• Compatible for 1S Lipo/LIHV
  
• Recommend 1S 450mah/550mah/650mah battery(Not include)

Specifications

• Item Name: HappyModel BNF 1S Mobula7 Analog Whoop - Choose Receiver Type
• Wheelbase: 75mm
  
• Size: 99mm x 99mm x 40mm
  
• Weight: 24g
• Receiver option:
  -2.4G ELRS SPI
  -SPI Frsky D8/D16  not compatible with EMAX E6 radio
  -TBS version(with external TBS CRSF NANO RX)

Motor

• Mode: RS0802 KV20000
  
• Configu-ration:9N12P
  
• Stator Diamter:8mm
  
• Stator Length:2mm
  
• Shaft Diameter:Φ1.5mm
  
• Motor Dimension(Dia.xLen):Φ10.5mm x 13.5mm
  
• Weight(g):2.0g
  
• No.of Cells(Lipo):1S only

Propellers

• Weight:0.24g
  
• Material:PC
  
• Pitch:1 inchProps Dia:40mm
  
• Center Thickness:5mm
  
• Center Hole Dia:1.5mm

Flight Controller

• X12 ELRS V1.0 flight controller built-in ELRS 2.4G receiver Target: CRAZYBEEF4SX1280
  
• X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
  
• X12 PNP V1.0 flight controller with external TBS CRSF Nano receiver Target: CRAZYBEEF4DX
  
• X12 PNP V1.0 flight controller without onboard receiver Target: CRAZYBEEF4DX
  
• MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
  
• Sensor: MPU6000 or ICM20689 or BMI270(SPI connection)
  
• Mount hole size: 25.5mm x 25.5mm
  
• Power supply: 1S battery input (DC 2.9V-4.35V)
  
• Built-in 12A(each) Blheli_S 4in1 ESC
  
• Built-in Betaflight OSD(SPI Control)
  
• Built-in 5.8G OpenVTX 0mw~400mw
  
• Built-in ExpressLRS 2.4G,Frsky D8/D16
  
• Built-in voltage detection
  
• Built-in current sensor

Onboard 4in1 ESC

• Power supply: 1S LiPo/LiPo HV
  
• Current: 12A continuous peak 15A (3 seconds)
  
• Support BLHeliSuite programmable
  
• Factory firmware: Z_H_30_REV16_7.HEX
  
• Default protocol: DSHOT300
  
• Support Bluejay firmware
  
• When use Blujay firmware with 48khz, should set startup power to 1100/1200

Receiver 

• ExpressLRS 2.4GHz
  • Packet Rate option: 50Hz/150Hz/250Hz/500Hz
    
  • ExpressLRS Firmware version: V2.0
    
  • RF Frequency: 2.4GHz
    
  • Antenna : SMD antenna
    
  • Telemetry output Power: <12dBm
    
  • Receiver protocol:  SPI ExpressLRS
    
  • Compatible with ExpressLRS V2.0 TX Module
    
  • Couldn’t flash separately ExpressLRS firmware
• Frsky SPI D8/D16
  • SPI BUS receiver Frsky D8 compatible
    
  • Compatible Non EU transmitter D8 modelChannels: 8ch
    
  • No ground interference ( Transmitter and receiver 1 m from the ground): 200meterFailsafe support
• Onboard 5.8 OPENVTX
  • Firmware version: OPENVTX
    
  • Smartaudio v2.1
    
  • PIT Mode support
    
  • RCE Mode support
    
  • Channels:48ch
    
  • Transmitting Power: 0/RCE/25mw/100mw/400mw
    
  • Power supply: DC 5V
    
  • Current (5v):650ma~1000ma
• CaddxFPV ANT Camera
  • Image Sensor: 1/3″ CMOS Sensor
    
  • Horizontal Resolution: 1200 TVL
    
  • TV System: NTSC or PAL
    
  • IMAGE: 16:9 or 4:3
    
  • Synchronization: Internal
    
  • Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
    
  • S/N Ratio : >52dB (AGC OFF)
    
  • Video Output: CVBS
    
  • Lens: 1.8mm
    
  • Min. Illumination: 0.001Lux@F1.2
    
  • Auto Gain Control: YES
    
  • WDR: Global WDR
    
  • DNR: 3D DNR
    
  • Dimensions: 14x14mm(with bracket to 19x19mm)
    
  • Wide Power Input: DC 3.7-18V
    
  • Weight: 2g (N.W.)

Includes

• 1x HappyModel BNF 1S Mobula 7 Whoop