"Okay I want to like happymodel but I’ve bought their frsky mobula 6 and that didn’t even bind out of the box so I couldn’t even fly that. Then this drone I got it binded it and it was a lot of fun but after a small crash it had the worst wobble no clue what happened. It’s still not fixed and support answered once then never answered again."
Details
Description
The Happymodel Mobula6 2024 1S 65mm Ultra Light Micro FPV 1S Whoop comes equipped with a lightweight AIO flight controller and 2.4Ghz ELRS receiver. The drone is Ready to Rip!
Check out our other pre-built quads, as well as the rest of our HappyModel selection!
Features
- AIO Flight controller with Serial ELRS Receiver and 5.8G Openvtx
- Super light 1S 65mm Brushless whoop only 17.7g
- Equipment with the lightest brushless motors-SE0702 only 1.46gram
- FX17-B 1/3 CMOS 800TVL Camera awesome footage
- Smooth and powerful
- Compatible for 1S Lipo/LIHV
Specifications
- Wheelbase: 65mm
- Size: 81mm x 81mm x 37mm
- Weight: 17.7g
- Option:
-V1 version with SuperX ELRS V1.0 AIO
-V2 version with SuperX ELRS V2.0 AIO
The only difference is v2.0 AIO FC comes with motor plug but V1.0 AIO FC is no motor plug.
Motors
- Mode: SE0702 KV28000
- Configu-ration: 9N12P
- Stator Diamter: 7mm
- Stator Length: 2mm
- Shaft Diameter: Φ1mm
- Motor Dimension(Dia.xLen): Φ9.5mm x 14mm
- Weight(g): 1.46g
- No.of Cells(Lipo): 1S only
Propellers
- Materials: PC
- Inch: 31mm
- Pitch: 0.8 in
- Weight: 0.21g
- Mount hole diameter: 1mm
AIO
- SuperX ELRS AIO 5-IN-1 Flight controller
- MCU:STM32F411CEU6 (100MHZ, 512K FLASH) ,ESP32-PICO-D4
- Sensor:BMI270(SPI connection)
- Mount hole size: 25.5mm x 25.5mm
- Power supply: 1S battery input (DC 2.9V-4.35V)
- Built-in 5A(each) Blheli_S 4in1 ESC
- Built-in Betaflight OSD(SPI Control)
- Built-in 5.8G OpenVTX 0mw~400mw (MSP control)
- Built-in UART ExpressLRS v3.0.0
- Built-in voltage meter sensor , voltage meter scale 110
- Built-in current meter sensor , current meter scale 1175
- Power supply: 1S LiPo/LiPo HV
- Current: 5A continuous peak 6A (3 seconds)
- Support BLHeliSuite programmable
- Factory firmware: Bluejay v0.19.2
- Default protocol: DSHOT300
- Recommend ESC Startup power value to min1100/max1200
Onboard Serial ExpressLRS receiver
- Packet Rate option: 50Hz/150Hz/250Hz/500Hz
- ExpressLRS Firmware version: V3.0
- RF Frequency: 2.4GHz
- Antenna : Enameled copper wire antenna
- Telemetry output Power: <12dBm
- Receiver protocol: Serial_based CRSF
- Compatible with ExpressLRS V3.x.x TX Module
- Could flash single ELRS receiver firmware by Wifi
- ExpressLRS firmware target: ExpressLRS firmware target:
- HappyModel AIO 2.4GHz RX+VTX (ExpressLRS web flasher)
- Available from Expresslrs version 3.4.0 RC2
Onboard VTX
- Firmware version: OPENVTX
- MSP VTX
- PIT Mode support
- Channels:40ch
- Transmitting Power: 0/RCE/25mw/100mw/400mw
- Power supply: DC 5V
- Current (5v): <650ma (400mw)
- Antenna connector: U.FL
FX17-B Camera
- Model: FX17-B
- Image Sensor: 1/3″ CMOS
- Horizontal Resolution: 800TVL
- FOV 150°
- Signal System: NTSC
- Net Weight: 1.5g
- Dimensions: L14mm x W14mm x H13mm
Includes
- 1x HappyModel BNF 2024 V1 Mobula6 ELRS 65mm Ultra Light Brushless Analog Whoop - ELRS 2.4GHz +Canopy
- 1x Option1: SuperX ELRS AIO 5-IN-1 Flight controller V1.0
- or 1x Option2: SuperX ELRS AIO 5-IN-1 Flight controller V2.0
- 4x SE0702 KV28000 brushless motor
- 1x Gemfan 1208-3 31mm tri-blade propellers(4cw+4ccw)
- 1x FX17-B 1/3 CMOS 800TVL camera NTSC 4:3
- 1x Onboard 5.8G 25mw~400mw VTX
- 1x Spare canopy
- 1x Propeller disassemble tool
- 1x Screw driver
More Info
- SKU: HAPP-5A10087
- Barcode: 6910236006018