Skip to content

SpeedyBee V3 F722 3-6S 30x30 Stack/Combo (F722 FC / 50A 32bit 4in1 ESC)

Original price $119.99
Original price $119.99 - Original price $119.99
Original price $119.99
Current price $89.99
$89.99 - $89.99
Current price $89.99
In Stock
Pre Order
Coming Soon
Free Delivery on U.S.A. Orders $99 or more

Add To Wishlist

The SpeedyBee V3 F722 3-6S 30x30 Stack/Combo (F722 FC / 50A 32bit 4in1 ESC) is a marvel to behold. The latest iteration of the SpeedyBee Stack, the V3 is packed with powerful new upgrades. Faster Wi-Fi upgrades, black box retrieval within a minute, supports up to 8 motors, and features soldering pads on one end, and pin connectors on the other in case soldering isn't your thing. The 50A 4in1 ESC is fitted with a high-quality CNC heat sink shield to significantly reduce the heat from your MOSFETs ensuring stable current flow at a high-throttle position. This ESC should have no issues with overheating. A great benefit in a stylish blue finish.

Check out our other 30x30 Stacks and all our Speedy Bee products!

SpeedyBee F7V3 STACK SpeedyBee F7V3 STACK


F722 2-6S Flight Controller

  • MCU: STM32F722
  • IMU: BMI270
  • USB: Type-C
  • Baro: BMP280 (I2C)
  • OSD: BetaFlight OSD w/ AT7456E chip
  • BLE Support, used for Flight Controller configuration
  • WiFi Support, used for data transfer, e.g firmware flashing, and Blackbox analysis.
  • DJI Air Unit plug: A full DJI Air Unit JST slot onboard
  • BlackBox: 500MB onboard data flash
  • BetaFlight Camera Control Pad: Yes
  • Power input: 3S - 6S Lipo
  • 10 groups of 5V output, three +5V pads and 1 BZ+ pad (used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.
  • 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.
  • Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
  • Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
  • ESC signal M1 - M4 on bottom side and M5-M8 on front side.
  • UART: 5 sets (UART1, UART2, UART3, UART4, UART6)
  • ESC Telemetry: UART UART4 RX
  • I2C: Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
  • LED: Used for WS2812 LED controlled by Betaflight firmware.
  • Buzzer: BZ+ and BZ- pad used for 5V Buzzer
  • Boot button: Yes
  • RSSI input: Yes
  • SmartPort: Supported
  • Support Flight Controller Firmware: BetaFlight(Default), EMUFlight, INAV
  • Target: SPEEDYBEEF7V3
  • Mounting: 30.5x30.5mm, 4mm hole size
  • Dimension 41(L) x 38(W) x 8.1(H)mm
  • Weight 9g

32Bit 50A 3-6S 4in1 ESC

  • Firmware: SpeedyBee BL32 50A
  • Continuous Current: 50Ax4
  • Burst Current: 55A(5S)
  • Power input: 3S - 6S LiPo
  • Power output: VBAT
  • Current Sensor: Supported (Scale=490 Offset=0)
  • Mounting: 30.5x0.5mm, 4mm hole size
  • Dimension: 45.6(L)x40(W)x8.8mm(H)
  • Weight: 19.2g with heat sink


  • 1x SpeedyBee BL32 32bit 50A 3-6S 30x30 4in1 ESC