• TINYSLEDS LED TinysLEDs SaddleLites V2 RGB LED 4 Pack
  • TINYSLEDS LED TinysLEDs SaddleLites V2 RGB LED 4 Pack
  • TINYSLEDS LED TinysLEDs SaddleLites V2 RGB LED 4 Pack
  • TINYSLEDS LED TinysLEDs SaddleLites V2 RGB LED 4 Pack
1 4

TinysLEDs SaddleLites V2 RGB LED 4 Pack

TinysLEDs SaddleLites V2 RGB LED 4 Pack

$14.49
$14.49
Add To Wishlist
View full details

Details

Description

How do you mount LEDs to the side of a quad? It has always been a challenge until now! Just Slide these on like a saddle on a horse. Easy to install, Compact and hard to damage. No extra weight of TPU mounting or special tape or glue. The most clean install possible. LEDs are configured to act as 1 chip in your configuration. This ensures maximum safety for racing. No strings going out due to a damaged chip. 

Version 2 now includes a data out pad.

Check out all our LEDs and our TinysLEDs selection! 

Betaflight or Other Flight Controller Setup instructions:

Setup 1 LED in your Flight controller software. The saddlelite is 4 leds with the same signal. 

Specifications

  • Input Voltage: 5V (Requires LED Signal)
  • Current Draw: 150ma MAX per board on white. 
  • Dimensions: 10 x 9 x 5 mm
  • Weight: 1 gram w/o wires

Includes

  • 4x TinysLEDs Saddle Lites V2 RGB LED

More Info

  • SKU: TINY-SaddleLights-4pack
  • Barcode: 691023502987
 

Overall rating: 4.4242425 / 5 from 33 reviews.

AI Generated Review Summary

Summary topics

Review topics: ["light","design","wires","leds","mount","install","guys","plenty","holes"].

Review highlights

Reviews

Great

"These led’s are great. Easy to mount , super bright and addressable. I will be putting these. On every quad I can"

— Garrett J. (5/5)

Good tiny led for small craft.

"These are great very bright but delicate."

— Rich H. (5/5)

really helps with Line of Site

"I Added these to a Diatone 349 two facing back yellow and in the front port=red/starboard=green facing left and right. Each saddle can only be a single color as noted deeper in the details, but these make it very easy to verify my orientation when flying line of site. Wiring them up is a little tight for a novice in soldering, but I managed was helpful to have the input in and input out as separate "pads" on the V2 version."

— Steven B. (4/5)

Tiny's satellite led

"Like them there small well tiny and plenty for what I need"

— Edward H. (5/5)

I needed a solution to

"I needed a solution to make my quad visible from the rear. My friend and I like to chase each other around and he had just hit (and destroyed) my wing which had minimal lighting. These will definitely eliminate any excuse for "I didn't see you" comments!"

— Darren H. (5/5)

Good for compliance

"Good form factor and easy to setup."

— Clayton C. (5/5)

Doesn't work1

"None of the LEDs respond or light up. Using a Darwin F411. Betaflight configuration is correct. Setup was tested against other functioning LEDs (they worked normally). Wanted to have all 4 in parallel. Didn't work. Tried all 4 individually. Didn't work for any of them. All wires and connections passed a continuity check. All the connections were confirmed to be correct. The voltage was confirmed to be 4.991V. Worthless trash."

— fŸck y. (1/5)

Small builds

"Perfect for small builds!"

— Rick C. (5/5)

It’s tiny, RGB capable, and

"It’s tiny, RGB capable, and super bright. It’s unique layout lets you install these leds on stand-offs or screws. The design also allows you to potentially swivel the lights to an angle you like. Need mooooore!"

— Samuel S. (5/5)

Great little LEDs to add

"Great little LEDs to add to ur quad. Easy install and are bright. They are fairly exposed after mounting so I would expect them to take damage from repeated crashes or mid-air contact while racing."

— Joshua C. (5/5)

Q&A