Menu
Wishlist 0 Cart 0

Mobula7 Whoop by HappyModel - Basic / Standard Kit - FRSKY, DSMX, FLYSKY


In Stock
Add to Wishlist

***Manufacturer provided delivery date of Nov 26th. That could change! We expect a partial delivery of the Basic units around Nov 20th, the rest will deliver around the 26th. Pre-orders for Basic kits placed on/before approx Nov 7th will get the first small shipment. After then may wait until the full delivery around the 26th. THESE DATES ARE NOT GUARANTEED.***

Whoops have gone to the next level! As a direct competitor to the EMAX TinyHawk, the Mobula7 has taken the internet by storm given its speed and capabilities in such a small package. Check out the video and specs of the Mobula 7 by Happy Model below!


Specification: 
Brand Name: Happymodel
Model: Mobula 7
Item Name: 75mm Wheelbase 2S Brushless Whoop FPV Racing Drone
Wheelbase: 75mm

Version: Basic Version / Standard Version ( Optional)
- The diffirence of them are the package charger.
   Basic Version: USB Charger
   Standard Version: 6-way Charger

Receiver ( Optional): Compatible Frsky NON-EU Receiver
                                      Compatible Frsky EU-LBT   Receiver  ( XM+ Receiver)
                                      Compatible Flysky AFHDS/ AFHDS-2A Receiver
                                      Compatible DSM2/DSMX Receiver

Size: 98mm*98mm*36mm

Weight: 25.9g (without battery)
This is compatible with our 250mah HV Whoop Batteries

Crazybee F3 Pro Flight Controller Item Name: Crazybee F3 Pro FC
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1-2S battery input (DC 3.5-8.7V)

Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Receiver ( Diffirent version having diffirent receiver)
Built-in Betaflight OSD(SPI Control)
Built-in Current meter Max 28A
Current meter scale set to 1175
Built-in 5V 1A BEC with LC filter

Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready

Firmware
(Frsky version) CRAZYBEEF3 PRO FR Firmware target: CrazybeeF3FR
(Flysky version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS
(DSM2/DSMX version) CRAZYBEEF3 PRO Firmware target: CrazybeeF3DX
(Frsky EU-LBT version) CRAZYBEEF3 PRO FS Firmware target: CrazybeeF3FS
 
Onboard 5A 4 In 1 ESC

Power supply: 1-2S LiPo/LiPo HV (3.5v/8.7v)
MCU upgraded to EFM8BB21
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: S_H_50_REV16_7
Default protocol: DSHOT600

Onboard Frsky NON-EU receiver Version
SPI BUS receiver
Frsky D8/D16 switchable
Compatible Non EU transmitter both D8 and D16 mode

Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 
Onboard Frsky EU-LBT Version
(External XM+ receiver)
 

Operating Voltage Range: 3.7~10V
Operating Current: 30mA @5V
Operating Range: Full range
With RSSI output on board: Analog 0~3.3V
Firmware Upgradeable, Default firmware EU-LBT with RSSI

Onboard Flysky receiver Version
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 

Onboard DSM2 / DSMX receiver version

Serial bus receiver
Protocol: DSM2/DSMX compatible
Channels:6-9 (Depend on your radio)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
 
SE0802 16000KV Motor
Model: SE0802
KV: 16000KV
Configu-ration: 9N12P Stator Diamter: 8mm Stator Length: 2mm Shaft Diameter: Φ1.0 Motor Dimension (Dia.*Len) : Φ10.5*14.5mm Weight: 1.8g
Support 1-2S Lipo
 
No.of Cells: 1S Lipo
Propeller
40mm 4-blade Propeller ( 4 CW + 4 CCW)
 

5.8G VTX AIO Camera
 

5.8G 40CH 25mW VTX
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)

700TVL FOV120 Camera
Camera resolution: 700TVL
Field of view: 120°
Video Format: NTSC
Antenna: RG178 antenna
Frequency: 5.8GHz 5bands 40 channels
With Raceband
Smartaudio ready(Frsky EU-LBT and DSMX version not compatible)
Size: 13.9"12.0mm ( L*W )
Weight: 3g
 
Lipo Battery
Capacity:250mAh
Voltage:3.8v
Continuous Discharge Rate: 30C
Instantaneous discharge rate: 60C
Size: 55mmx12mmx7mm
Weight: 6.5g
Connector: PH2.0
Notes: Need 2pcs batteries for Series circuit
 


Features:
- New Crazybee F3 PRO Flight controller 1-2s Lipo compatible
- 2S whoop more powerful and more flight time
- Betaflight support , multi flight mode: ACRO/AIR/ANGLE
- New 0802 Powerful and High efficiency Brushless motor and Smooth ESC
- Smartaudio ready , change VTX bands, channels via OSD
  DSM2/DSMX and Frsky EU-LBT version are Serial-based receiver, so Smartaudio is not compatible.
- Adjust the settings and the PID of the flight controller via OSD
- Frsky Non-EU version support NON-EU Frsky transmitter D8/D16 compatible
- Flysky version support both AFHDS and AFHDS-2A protocol transmitter
- DSM2/DSMX version support DSM2 and DSMX compatible Spektrum transmitter
- Frsky EU-LBT version support Frsky EU-LBT firmware transmitter
- Full telemetry function ready
- Head lights ready
- Camera angle adjustable
- Real Bind and Fly version
- Buzzer Ready

Package Included:
Basic Version
1x Mobula7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
4x 3.8v 250mah 30C/60C Lipo battery
1x USB Lipo/LIHV Charger
1x Fixing Mount for Lipo Battery
1x Propeller Disassemble Tool
1x Screwdriver

Standard Version
1x Mobula7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
4x 3.8v 250mah 30C/60C Lipo battery
1x 1S06 6 Way Lipo/LIHV charger
1x Propeller Disassemble Tool
1x Fixing Mount for Lipo Battery

1x Screwdriver 


Mobula7 Whoop by HappyModel
Mobula7 Basic Kit


FRSKY Whoop
Standard Whoop Kit

Mobula7







Sale

Unavailable

Sold Out

Add to Wishlist