HappyModel BNF Crux3 3" Quad - Choose Your RX
The DSMX version is not currently not compatible with Spektrum DXE and DX6E radio transmitter. HappyModel is working on fixing this with the next release of BetaFlight.
A zippy 3" toothpick BNF, perfect for any size outdoor space. Includes a TPU mount for your insta360 go and operates on a variety of 2S Lipo batteries
Check out the HappyModel Crux3 Quad and Accessories Collection.
Be sure to check out all our pre-built quads, and all our Happymodel products!
Specifications
- Wheelbase: 115mm
- Size: 97x97x35mm (without propellers)
- Weight: 41g (without battery)
- Recommend Lipo Battery: 2s 350mah/400mah/450mah/520mah Battery ( NOT Included)
EX1202.5 6400KV Motor
- Configuration :9N12P
- Stator Diamter: 12mm
- Stator Length: 2.5mm
- Shaft Diameter: Φ1.5mm
- Motor Dimension(Dia.*Len): Φ14*14.5mm
- Weight: 4.4g
- No.of Cells(Lipo): 1-2S
Gemfan 3018 2-Blade Propeller
- Center Thickness: 5.5mm
- Prop Diameter: 76.5mm
- Center Hole diameter: 1.5mm
CrazybeeX FR V2.2 F4 Flight Controller
- MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
- Sensor: MPU6000 (SPI connection)
- Board Size: 28.5x28.5mm
- Power Supply: 1-2S battery input (DC 2.9V-8.7V)
- Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
- Built-in Betaflight OSD(SPI Control)
- Built-in 5.8G VTX
- Built-in SPI Frsky/Flysky receiver or no receiver
- Built-in 5V 1A BEC
- (Frsky SPI RX Version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR
- (Flysky SPI RX Version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS
- (DSM2/X SPI RX Version)CRAZYBEEX DXS V1.0 FC firmware target: CrazybeeF4DXS
- (External Frsky RXSR Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX
- (External TBS CRSF NANO Version) CRAZYBEEX PNP V2.2 Firmware target: CrazybeeF4DX
- Onboard 5A BL_S 4in1 ESC
- MCU upgraded to EFM8BB21
- Power supply: 1S LiPo/LiPo HV
- Current: 5A continuous peak 6A (3 seconds)
- Support BLHeliSuite programmable
- Factory firmware: S_H_50_REV16_7.HEX
- Default protocol: DSHOT600
- SPI BUS receiver Frsky D8 compatible
- Compatible Non EU transmitter D8 model
- Channels: 8ch
- Failsafe support
- No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
Onboard Flysky SPI receiver Version (Optional)
- Protocol: AFHDS and AFHDS-2A Switchable
- Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
- No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m
- Failsafe support
Onboard DSM2/X SPI receiver Version (Optional)
- SPI BUS receiver DSM2/DSMX compatible
- Channels: Max 12ch
- Failsafe support
- No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
- RSSI enable (show on the goggles)
External Frsky R-XSR receiver version (Optional)
- Weight: 1.5g
- Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel)
- Operating Voltage Range: 3.5V~10V
- Operating Current:70mA@5V
- Firmware Upgradable
- Compatibility: FrSky X Series modules and radios in D16 mode
- Could support Frsky New ACCESS Protocol ( Upgrade firmware)
External TBS CRSF Nano receiver version (Optional)
- Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible
- Output power: 25mw~200mw switchable
- Frequency: 40CH
- Input voltage: 3.3V 5.5V
- Current consumption: 300mA(type)
- Frequency: 5.8GHz 5bands 40 channels
- With Race band
- Smartaudio ready
- Image Sensor: 1/3" CMOS Sensor
- Horizontal Resolution: 1200 TVL
- TV System: NTSC or PAL Switchable
- IMAGE: 4:3
- Synchronization: Internal
- Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000
- S/N Ratio : >52dB (AGC OFF)
- Video Output: CVBS
- Lens: 1.8mm
- Min. Illumination: 0.001Lux@F1.2
- Auto Gain Control: YES
- BLC: YES
- WDR: Global WDR
- DNR: 3D DNR
- Dimensions: 14*14mm(with bracket to 19*19mm)
- Wide Power Input: DC 3.7-18V
- Work Temperature: -20℃~+60℃
- Weight: 2g
Includes
- 1x HappyModel BNF Crux3 3" Quad - Choose Your RX